HomeHelpSearchLoginRegister  
 
Latest Threads 
Page Index Toggle Pages: 1
Print
My Tesla Powerwall Is Here! 7.5 KWh Power Curve Explanation Tech Info DIY (Read 839 times)
electron
Senior Member
****
Offline



Posts: 334
My Tesla Powerwall Is Here! 7.5 KWh Power Curve Explanation Tech Info DIY
Nov 19th, 2016 at 4:28am
 
My version of the Tesla Powerwall using Nissan Leaf (EV car) Batteries.

I posted this video on 02/26/2016 and about a week later I added 3 more "modules" so I am currently at 9 KWh (which is about 6.7 KWh out of the inverter AC plug). This is enough for a typical night running lights and computers and the fridge etc...

I have had NO BALANCING problems at all! Look at the way they are connected, you will see a lot of parallel cell connections and also I only have 6 cells in series for "24V", the less cells in series the less balancing problems! Plus they were all manufactured at the same time and same chemicals.


http://www.youtube.com/watch?v=uC12qdkExTE

YouTube Video Description:

Published on Feb 26, 2016
MORE DETAILS: First thing you should do is solar power your hot water heater because it is the #2 thing in the house that pulls BIG power and you can do it more direct without inverters or batteries see:
http://techluck.com

Your water heater is like a 6 KWh heat battery that you pay to charge every day! And it's already installed! Why not put it on solar the easy way?

With the Li-Ion batteries there's no more battery acid checking or fumes and takes up less space. They can be partly charged with no problems.

To get an idea of the size of these, it's about 3 car batteries in that same space of the 3 stacks.

My "wall" has more configuring to be done with things that give me power in the daytime. The batteries are just for night and are just one system. So stay tuned! (please subscribe)

Note that a actual Tesla Powerwall is just the battery and is high voltage of around 350V. You need to add a special inverter which is generally 2000W with other features like grid switch over which you can DIY if you have some electrical skills. My system is 24V and uses a standard pure sine wave inverter and 24V charge controllers (modified, see below).

If you are worried about a BMS and balancing the batteries, remember they are mostly in parallel, not a big string all in series. I have been monitoring them and so far they are OK. I can easily bottom balance them if needed. See how they are connected in the video.

The Ford Fusion hybrid battery looks promising for easy DIY, it has easy to use screw terminals also. Check out these videos:
http://www.youtube.com/watch?v=B640f88Uhls
http://www.youtube.com/watch?v=x95dgVRpPp4

See this also:  Hyundai Sonata Hybrid battery
https://www.youtube.com/watch?v=wY3IyCRlVRA
https://www.youtube.com/watch?v=QLSMxBxOu1w

My Nissan Leaf Battery modules were purchased from:
http://hybridautocenter.com/
Hybrid Auto Center, Las Vegas, NV

Everyone is doing this now and for many reasons, see this video about home batteries and a new battery type near the end:
http://www.youtube.com/watch?v=yxABosWfuus

Details on how I modified those little low cost charge controllers:
http://techluck.com/cgi-bin/YaBB.pl?num=1313110955

NISSAN LEAF BATTERY CELL - FIRE and DESTRUCTION TESTS
Screwdriver puncture, torch test, NOTHING HAPPENS!
https://www.youtube.com/watch?v=Jz37WycW-7E
Flat batteries just outgas:
https://www.youtube.com/watch?v=RXDAzBVjwuM

Li-Ion CELLS GENERALLY ALL OF THEM which makes it
easy to figure out.
4.2V is full charge
2.5V is dead and do not go below or over those voltages or DAMAGE!

Solar Powered Off Grid Free Energy PV EV Li-Ion DIY Smart Meter Grid Tie Inverter Explanation Solar Hot Water Heating powerwall home improvement prepper rv cabin energy generator clean
Back to top
 
Page Index Toggle Pages: 1
Print